Jump to content
Règlement du forum ×
IPTV et arnaques ×

Recommended Posts

Salut,

voila donc mon lucid met un temps plus grand à ce charger que karmic alors qu'il est supposé etre moins,le fichier journal dmesg me montre qu'il perd +18 sec à essayer de monter le lecteur de carte mémoire avant qu'il ne s'aperçoit qu'il y en a pas de carte insérer.

donc ma question est : est-ce qu'on peut faire en sorte qu'ubuntu ignore le lecteur de carte mémoire pendant le démarrage système ?

voila le fichier journal dmesg. merci

 

[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 2.6.32-22-generic (buildd@palmer) (gcc version 4.4.3 (Ubuntu 4.4.3-4ubuntu5) ) #36-Ubuntu SMP Thu Jun 3 22:02:19 UTC 2010 (Ubuntu 2.6.32-22.36-generic 2.6.32.11+drm33.2)
[    0.000000] KERNEL supported cpus:
[    0.000000]   Intel GenuineIntel
[    0.000000]   AMD AuthenticAMD
[    0.000000]   NSC Geode by NSC
[    0.000000]   Cyrix CyrixInstead
[    0.000000]   Centaur CentaurHauls
[    0.000000]   Transmeta GenuineTMx86
[    0.000000]   Transmeta TransmetaCPU
[    0.000000]   UMC UMC UMC UMC
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[    0.000000]  BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 0000000070000000 (usable)
[    0.000000]  BIOS-e820: 0000000070000000 - 0000000080000000 (reserved)
[    0.000000]  BIOS-e820: 0000000080000000 - 00000000affa0000 (usable)
[    0.000000]  BIOS-e820: 00000000affa0000 - 00000000affae000 (ACPI data)
[    0.000000]  BIOS-e820: 00000000affae000 - 00000000afff0000 (ACPI NVS)
[    0.000000]  BIOS-e820: 00000000afff0000 - 00000000b0000000 (reserved)
[    0.000000]  BIOS-e820: 00000000b0000000 - 00000000c0000000 (usable)
[    0.000000]  BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[    0.000000]  BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[    0.000000]  BIOS-e820: 00000000ff700000 - 0000000100000000 (reserved)
[    0.000000] DMI present.
[    0.000000] AMI BIOS detected: BIOS may corrupt low RAM, working around it.
[    0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[    0.000000] last_pfn = 0xc0000 max_arch_pfn = 0x100000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-CFFFF write-protect
[    0.000000]   D0000-DFFFF uncachable
[    0.000000]   E0000-EFFFF write-through
[    0.000000]   F0000-FFFFF write-protect
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 000000000 mask F80000000 write-back
[    0.000000]   1 base 080000000 mask FC0000000 write-back
[    0.000000]   2 disabled
[    0.000000]   3 disabled
[    0.000000]   4 disabled
[    0.000000]   5 disabled
[    0.000000]   6 disabled
[    0.000000]   7 disabled
[    0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[    0.000000] Scanning 0 areas for low memory corruption
[    0.000000] modified physical RAM map:
[    0.000000]  modified: 0000000000000000 - 0000000000010000 (reserved)
[    0.000000]  modified: 0000000000010000 - 000000000009fc00 (usable)
[    0.000000]  modified: 000000000009fc00 - 00000000000a0000 (reserved)
[    0.000000]  modified: 00000000000e0000 - 0000000000100000 (reserved)
[    0.000000]  modified: 0000000000100000 - 0000000070000000 (usable)
[    0.000000]  modified: 0000000070000000 - 0000000080000000 (reserved)
[    0.000000]  modified: 0000000080000000 - 00000000affa0000 (usable)
[    0.000000]  modified: 00000000affa0000 - 00000000affae000 (ACPI data)
[    0.000000]  modified: 00000000affae000 - 00000000afff0000 (ACPI NVS)
[    0.000000]  modified: 00000000afff0000 - 00000000b0000000 (reserved)
[    0.000000]  modified: 00000000b0000000 - 00000000c0000000 (usable)
[    0.000000]  modified: 00000000fec00000 - 00000000fec01000 (reserved)
[    0.000000]  modified: 00000000fee00000 - 00000000fee01000 (reserved)
[    0.000000]  modified: 00000000ff700000 - 0000000100000000 (reserved)
[    0.000000] initial memory mapped : 0 - 00c00000
[    0.000000] init_memory_mapping: 0000000000000000-00000000377fe000
[    0.000000] Using x86 segment limits to approximate NX protection
[    0.000000]  0000000000 - 0000400000 page 4k
[    0.000000]  0000400000 - 0037400000 page 2M
[    0.000000]  0037400000 - 00377fe000 page 4k
[    0.000000] kernel direct mapping tables up to 377fe000 @ 10000-15000
[    0.000000] RAMDISK: 37403000 - 37fef80f
[    0.000000] Allocated new RAMDISK: 008de000 - 014ca80f
[    0.000000] Move RAMDISK from 0000000037403000 - 0000000037fef80e to 008de000 - 014ca80e
[    0.000000] ACPI: RSDP 000fa450 00014 (v00 MSI_NB)
[    0.000000] ACPI: RSDT affa0000 0004C (v01 MSI_NB MEGABOOK 09252009 MSFT 00000097)
[    0.000000] ACPI: FACP affa0200 00084 (v01 MSI_NB MEGABOOK 09252009 MSFT 00000097)
[    0.000000] ACPI: DSDT affa0680 099AB (v01 MSI_NB MEGABOOK 00000010 INTL 20051117)
[    0.000000] ACPI: FACS affae000 00040
[    0.000000] ACPI: APIC affa0390 00080 (v01 MSI_NB MEGABOOK 09252009 MSFT 00000097)
[    0.000000] ACPI: MCFG affa0410 0003C (v01 MSI_NB MEGABOOK 09252009 MSFT 00000097)
[    0.000000] ACPI: SLIC affa0450 00176 (v01 MSI_NB MEGABOOK 09252009 MSFT 00000097)
[    0.000000] ACPI: WDRT affa05d0 00047 (v01 MSI_NB MEGABOOK 09252009 MSFT 00000097)
[    0.000000] ACPI: ECDT affa0620 00055 (v01 MSI_NB MEGABOOK 09252009 MSFT 00000097)
[    0.000000] ACPI: OEMB affae040 00078 (v01 MSI_NB MEGABOOK 09252009 MSFT 00000097)
[    0.000000] ACPI: HPET affaa680 00038 (v01 MSI_NB MEGABOOK 09252009 MSFT 00000097)
[    0.000000] ACPI: NVHD affae0c0 00284 (v01 092509  NVHDCP  09252009 MSFT 00000097)
[    0.000000] ACPI: SSDT affaec50 004F0 (v01 MSI_NB MEGABOOK 09252009 INTL 20051117)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] 2184MB HIGHMEM available.
[    0.000000] 887MB LOWMEM available.
[    0.000000]   mapped low ram: 0 - 377fe000
[    0.000000]   low ram: 0 - 377fe000
[    0.000000]   node 0 low ram: 00000000 - 377fe000
[    0.000000]   node 0 bootmap 00011000 - 00017f00
[    0.000000] (9 early reservations) ==> bootmem [0000000000 - 00377fe000]
[    0.000000]   #0 [0000000000 - 0000001000]   BIOS data page ==> [0000000000 - 0000001000]
[    0.000000]   #1 [0000001000 - 0000002000]    EX TRAMPOLINE ==> [0000001000 - 0000002000]
[    0.000000]   #2 [0000006000 - 0000007000]       TRAMPOLINE ==> [0000006000 - 0000007000]
[    0.000000]   #3 [0000100000 - 00008d9e98]    TEXT DATA BSS ==> [0000100000 - 00008d9e98]
[    0.000000]   #4 [000009fc00 - 0000100000]    BIOS reserved ==> [000009fc00 - 0000100000]
[    0.000000]   #5 [00008da000 - 00008dd185]              BRK ==> [00008da000 - 00008dd185]
[    0.000000]   #6 [0000010000 - 0000011000]          PGTABLE ==> [0000010000 - 0000011000]
[    0.000000]   #7 [00008de000 - 00014ca80f]      NEW RAMDISK ==> [00008de000 - 00014ca80f]
[    0.000000]   #8 [0000011000 - 0000018000]          BOOTMAP ==> [0000011000 - 0000018000]
[    0.000000] found SMP MP-table at [c00ff780] ff780
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA      0x00000010 -> 0x00001000
[    0.000000]   Normal   0x00001000 -> 0x000377fe
[    0.000000]   HighMem  0x000377fe -> 0x000c0000
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[4] active PFN ranges
[    0.000000]     0: 0x00000010 -> 0x0000009f
[    0.000000]     0: 0x00000100 -> 0x00070000
[    0.000000]     0: 0x00080000 -> 0x000affa0
[    0.000000]     0: 0x000b0000 -> 0x000c0000
[    0.000000] On node 0 totalpages: 720687
[    0.000000] free_area_init_node: node 0, pgdat c0798720, node_mem_map c14cc200
[    0.000000]   DMA zone: 32 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 3951 pages, LIFO batch:0
[    0.000000]   Normal zone: 1744 pages used for memmap
[    0.000000]   Normal zone: 221486 pages, LIFO batch:31
[    0.000000]   HighMem zone: 4369 pages used for memmap
[    0.000000]   HighMem zone: 489105 pages, LIFO batch:31
[    0.000000] Using APIC driver default
[    0.000000] ACPI: PM-Timer IO Port: 0x4008
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
[    0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] ACPI: IRQ14 used by override.
[    0.000000] ACPI: IRQ15 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] ACPI: HPET id: 0x10de8201 base: 0xfed00000
[    0.000000] SMP: Allowing 4 CPUs, 2 hotplug CPUs
[    0.000000] nr_irqs_gsi: 24
[    0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[    0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[    0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[    0.000000] Allocating PCI resources starting at c0000000 (gap: c0000000:3ec00000)
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:4 nr_node_ids:1
[    0.000000] PERCPU: Embedded 14 pages/cpu @c3000000 s36024 r0 d21320 u1048576
[    0.000000] pcpu-alloc: s36024 r0 d21320 u1048576 alloc=1*4194304
[    0.000000] pcpu-alloc: [0] 0 1 2 3 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 714542
[    0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.32-22-generic root=UUID=55c3d15f-e540-4ec0-bc35-6069b44fa05b ro vga=769 nomodeset video=uvesafb:mode_option=1440x900-24,mtrr=3,scroll=ywrap
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Enabling fast FPU save and restore... done.
[    0.000000] Enabling unmasked SIMD FPU exception support... done.
[    0.000000] Initializing CPU#0
[    0.000000] xsave/xrstor: enabled xstate_bv 0x3, cntxt size 0x240
[    0.000000] allocated 15728320 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.000000] Initializing HighMem for node 0 (000377fe:000c0000)
[    0.000000] Memory: 2820228k/3145728k available (4673k kernel code, 61316k reserved, 2121k data, 656k init, 1973896k highmem)
[    0.000000] virtual kernel memory layout:
[    0.000000]     fixmap  : 0xfff1d000 - 0xfffff000   ( 904 kB)
[    0.000000]     pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
[    0.000000]     vmalloc : 0xf7ffe000 - 0xff7fe000   ( 120 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xf77fe000   ( 887 MB)
[    0.000000]       .init : 0xc07a3000 - 0xc0847000   ( 656 kB)
[    0.000000]       .data : 0xc0590663 - 0xc07a2e48   (2121 kB)
[    0.000000]       .text : 0xc0100000 - 0xc0590663   (4673 kB)
[    0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[    0.000000] SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:2304 nr_irqs:440
[    0.000000] spurious 8259A interrupt: IRQ7.
[    0.000000] Console: colour dummy device 80x25
[    0.000000] console [tty0] enabled
[    0.000000] hpet clockevent registered
[    0.000000] HPET: 4 timers in total, 0 timers will be used for per-cpu timer
[    0.000000] Fast TSC calibration using PIT
[    0.000000] Detected 1999.936 MHz processor.
[    0.004006] Calibrating delay loop (skipped), value calculated using timer frequency.. 3999.87 BogoMIPS (lpj=7999744)
[    0.004028] Security Framework initialized
[    0.004052] AppArmor: AppArmor initialized
[    0.004061] Mount-cache hash table entries: 512
[    0.004198] Initializing cgroup subsys ns
[    0.004205] Initializing cgroup subsys cpuacct
[    0.004211] Initializing cgroup subsys memory
[    0.004220] Initializing cgroup subsys devices
[    0.004225] Initializing cgroup subsys freezer
[    0.004229] Initializing cgroup subsys net_cls
[    0.004253] CPU: L1 I cache: 32K, L1 D cache: 32K
[    0.004258] CPU: L2 cache: 2048K
[    0.004262] CPU: Physical Processor ID: 0
[    0.004266] CPU: Processor Core ID: 0
[    0.004272] mce: CPU supports 6 MCE banks
[    0.004282] CPU0: Thermal monitoring enabled (TM2)
[    0.004288] using mwait in idle threads.
[    0.004297] Performance Events: Core2 events, Intel PMU driver.
[    0.004309] ... version:                2
[    0.004312] ... bit width:              40
[    0.004316] ... generic registers:      2
[    0.004320] ... value mask:             000000ffffffffff
[    0.004324] ... max period:             000000007fffffff
[    0.004328] ... fixed-purpose events:   3
[    0.004331] ... event mask:             0000000700000003
[    0.004340] Checking 'hlt' instruction... OK.
[    0.023030] ACPI: Core revision 20090903
[    0.040010] ftrace: converting mcount calls to 0f 1f 44 00 00
[    0.040017] ftrace: allocating 21771 entries in 43 pages
[    0.044060] Enabling APIC mode:  Flat.  Using 1 I/O APICs
[    0.048277] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.087977] CPU0: Intel(R) Core(TM)2 Duo CPU     T6400  @ 2.00GHz stepping 0a
[    0.088001] Booting processor 1 APIC 0x1 ip 0x6000
[    0.008000] Initializing CPU#1
[    0.008000] CPU: L1 I cache: 32K, L1 D cache: 32K
[    0.008000] CPU: L2 cache: 2048K
[    0.008000] CPU: Physical Processor ID: 0
[    0.008000] CPU: Processor Core ID: 1
[    0.008000] CPU1: Thermal monitoring enabled (TM2)
[    0.172126] CPU1: Intel(R) Core(TM)2 Duo CPU     T6400  @ 2.00GHz stepping 0a
[    0.172156] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[    0.176019] Brought up 2 CPUs
[    0.176025] Total of 2 processors activated (7999.75 BogoMIPS).
[    0.176606] CPU0 attaching sched-domain:
[    0.176609]  domain 0: span 0-1 level MC
[    0.176612]   groups: 0 1
[    0.176619] CPU1 attaching sched-domain:
[    0.176621]  domain 0: span 0-1 level MC
[    0.176624]   groups: 1 0
[    0.176732] devtmpfs: initialized
[    0.176732] regulator: core version 0.5
[    0.176732] Time: 17:26:59  Date: 06/27/10
[    0.176732] NET: Registered protocol family 16
[    0.176732] Trying to unpack rootfs image as initramfs...
[    0.176732] EISA bus registered
[    0.176732] ACPI: bus type pci registered
[    0.176732] PCI: MCFG configuration 0: base fc000000 segment 0 buses 0 - 31
[    0.176732] PCI: Not using MMCONFIG.
[    0.176732] PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=8
[    0.176732] PCI: Using configuration type 1 for base access
[    0.180105] bio: create slab  at 0
[    0.181666] ACPI: EC: Detected MSI hardware, enabling workarounds.
[    0.181683] ACPI: EC: EC description table is found, configuring boot EC
[    0.181697] ACPI: EC: Look up EC in DSDT
[    0.182486] ACPI: EC: ASUSTek keeps feeding us with broken ECDT tables, which are very hard to workaround. Trying to use DSDT EC info instead. Please send output of acpidump to linux-acpi@vger.kernel.org
[    0.183813] ACPI: Executed 1 blocks of module-level executable AML code
[    0.191455] ACPI: Interpreter enabled
[    0.191475] ACPI: (supports S0 S3 S4 S5)
[    0.191499] ACPI: Using IOAPIC for interrupt routing
[    0.191569] PCI: MCFG configuration 0: base fc000000 segment 0 buses 0 - 31
[    0.205451] PCI: MCFG area at fc000000 reserved in ACPI motherboard resources
[    0.205462] PCI: Using MMCONFIG for extended config space
[    0.230238] ACPI: EC: GPE = 0x10, I/O: command/status = 0x66, data = 0x62
[    0.230724] ACPI: No dock devices found.
[    0.231220] ACPI: PCI Root Bridge [PCI0] (0000:00)
[    0.231481] pci 0000:00:03.0: reg 10 io port: [0x4f00-0x4fff]
[    0.231595] pci 0000:00:03.2: reg 10 io port: [0x4900-0x493f]
[    0.231611] pci 0000:00:03.2: reg 20 io port: [0x4d00-0x4d3f]
[    0.231617] pci 0000:00:03.2: reg 24 io port: [0x4e00-0x4e3f]
[    0.231643] pci 0000:00:03.2: PME# supported from D3hot D3cold
[    0.231651] pci 0000:00:03.2: PME# disabled
[    0.231833] pci 0000:00:03.5: reg 10 32bit mmio: [0xfae80000-0xfaefffff]
[    0.231932] pci 0000:00:04.0: reg 10 32bit mmio: [0xfae7f000-0xfae7ffff]
[    0.231967] pci 0000:00:04.0: supports D1 D2
[    0.231969] pci 0000:00:04.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.231976] pci 0000:00:04.0: PME# disabled
[    0.232017] pci 0000:00:04.1: reg 10 32bit mmio: [0xfae7ec00-0xfae7ecff]
[    0.232063] pci 0000:00:04.1: supports D1 D2
[    0.232065] pci 0000:00:04.1: PME# supported from D0 D1 D2 D3hot D3cold
[    0.232072] pci 0000:00:04.1: PME# disabled
[    0.232114] pci 0000:00:08.0: reg 10 32bit mmio: [0xfae78000-0xfae7bfff]
[    0.232150] pci 0000:00:08.0: PME# supported from D3hot D3cold
[    0.232157] pci 0000:00:08.0: PME# disabled
[    0.232232] pci 0000:00:0b.0: reg 10 io port: [0xb080-0xb087]
[    0.232238] pci 0000:00:0b.0: reg 14 io port: [0xb000-0xb003]
[    0.232243] pci 0000:00:0b.0: reg 18 io port: [0xac00-0xac07]
[    0.232248] pci 0000:00:0b.0: reg 1c io port: [0xa880-0xa883]
[    0.232254] pci 0000:00:0b.0: reg 20 io port: [0xa800-0xa80f]
[    0.232259] pci 0000:00:0b.0: reg 24 32bit mmio: [0xfae7c000-0xfae7dfff]
[    0.232344] pci 0000:00:10.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.232350] pci 0000:00:10.0: PME# disabled
[    0.232596] pci 0000:00:15.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.232607] pci 0000:00:15.0: PME# disabled
[    0.232877] pci 0000:00:16.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.232887] pci 0000:00:16.0: PME# disabled
[    0.233156] pci 0000:00:17.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.233167] pci 0000:00:17.0: PME# disabled
[    0.233436] pci 0000:00:18.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.233447] pci 0000:00:18.0: PME# disabled
[    0.233545] pci 0000:00:09.0: transparent bridge
[    0.233589] pci 0000:02:00.0: reg 10 32bit mmio: [0xfb000000-0xfbffffff]
[    0.233600] pci 0000:02:00.0: reg 14 64bit mmio pref: [0xe0000000-0xefffffff]
[    0.233610] pci 0000:02:00.0: reg 1c 64bit mmio pref: [0xf4000000-0xf5ffffff]
[    0.233617] pci 0000:02:00.0: reg 24 io port: [0xcc00-0xcc7f]
[    0.233624] pci 0000:02:00.0: reg 30 32bit mmio pref: [0xfafe0000-0xfaffffff]
[    0.233687] pci 0000:00:10.0: bridge io port: [0xc000-0xcfff]
[    0.233691] pci 0000:00:10.0: bridge 32bit mmio: [0xfaf00000-0xfbffffff]
[    0.233696] pci 0000:00:10.0: bridge 64bit mmio pref: [0xe0000000-0xf5ffffff]
[    0.233764] pci 0000:00:15.0: bridge io port: [0xd000-0xdfff]
[    0.233772] pci 0000:00:15.0: bridge 32bit mmio: [0xfe000000-0xfe9fffff]
[    0.233788] pci 0000:00:15.0: bridge 64bit mmio pref: [0xf6000000-0xf9efffff]
[    0.233839] pci 0000:06:00.0: reg 10 io port: [0xe800-0xe8ff]
[    0.233858] pci 0000:06:00.0: reg 18 64bit mmio: [0xfeaff000-0xfeafffff]
[    0.233871] pci 0000:06:00.0: reg 20 64bit mmio pref: [0xf9ff0000-0xf9ffffff]
[    0.233879] pci 0000:06:00.0: reg 30 32bit mmio pref: [0xfeac0000-0xfeadffff]
[    0.233915] pci 0000:06:00.0: supports D1 D2
[    0.233917] pci 0000:06:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.233925] pci 0000:06:00.0: PME# disabled
[    0.234002] pci 0000:00:16.0: bridge io port: [0xe000-0xefff]
[    0.234011] pci 0000:00:16.0: bridge 32bit mmio: [0xfea00000-0xfeafffff]
[    0.234026] pci 0000:00:16.0: bridge 64bit mmio pref: [0xf9f00000-0xf9ffffff]
[    0.234083] pci 0000:07:00.0: reg 10 64bit mmio: [0xfebf0000-0xfebfffff]
[    0.234223] pci 0000:00:17.0: bridge 32bit mmio: [0xfeb00000-0xfebfffff]
[    0.234381] pci_bus 0000:00: on NUMA node 0
[    0.234387] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.234572] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
[    0.234691] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.IXVE._PRT]
[    0.234775] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P8._PRT]
[    0.234858] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P9._PRT]
[    0.234944] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P6._PRT]
[    0.235027] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P7._PRT]
[    0.245673] ACPI: PCI Interrupt Link [LNKA] (IRQs 16 17 18 19) *0, disabled.
[    0.245970] ACPI: PCI Interrupt Link [LNKB] (IRQs 16 17 18 19) *0, disabled.
[    0.246260] ACPI: PCI Interrupt Link [LNKC] (IRQs 16 17 18 19) *0, disabled.
[    0.246550] ACPI: PCI Interrupt Link [LNKD] (IRQs 16 17 18 19) *0, disabled.
[    0.246842] ACPI: PCI Interrupt Link [LN0A] (IRQs 16 17 18 19) *0, disabled.
[    0.247130] ACPI: PCI Interrupt Link [LN0B] (IRQs 16 17 18 19) *0, disabled.
[    0.247420] ACPI: PCI Interrupt Link [LN0C] (IRQs 16 17 18 19) *0, disabled.
[    0.247709] ACPI: PCI Interrupt Link [LN0D] (IRQs 16 17 18 19) *0, disabled.
[    0.247998] ACPI: PCI Interrupt Link [LN1A] (IRQs 16 17 18 19) *0, disabled.
[    0.248290] ACPI: PCI Interrupt Link [LN1B] (IRQs 16 17 18 19) *0, disabled.
[    0.248578] ACPI: PCI Interrupt Link [LN1C] (IRQs 16 17 18 19) *0, disabled.
[    0.248868] ACPI: PCI Interrupt Link [LN1D] (IRQs 16 17 18 19) *0, disabled.
[    0.249156] ACPI: PCI Interrupt Link [LN2A] (IRQs 16 17 18 19) *0, disabled.
[    0.249445] ACPI: PCI Interrupt Link [LN2B] (IRQs 16 17 18 19) *0, disabled.
[    0.249733] ACPI: PCI Interrupt Link [LN2C] (IRQs 16 17 18 19) *0, disabled.
[    0.250021] ACPI: PCI Interrupt Link [LN2D] (IRQs 16 17 18 19) *0, disabled.
[    0.250310] ACPI: PCI Interrupt Link [LN3A] (IRQs 16 17 18 19) *0, disabled.
[    0.250599] ACPI: PCI Interrupt Link [LN3B] (IRQs 16 17 18 19) *0, disabled.
[    0.250888] ACPI: PCI Interrupt Link [LN3C] (IRQs 16 17 18 19) *0, disabled.
[    0.251175] ACPI: PCI Interrupt Link [LN3D] (IRQs 16 17 18 19) *0, disabled.
[    0.251471] ACPI: PCI Interrupt Link [LN4A] (IRQs 16 17 18 19) *10
[    0.251758] ACPI: PCI Interrupt Link [LN4B] (IRQs 16 17 18 19) *0, disabled.
[    0.252057] ACPI: PCI Interrupt Link [LN4C] (IRQs 16 17 18 19) *0, disabled.
[    0.252347] ACPI: PCI Interrupt Link [LN4D] (IRQs 16 17 18 19) *0, disabled.
[    0.252642] ACPI: PCI Interrupt Link [LN5A] (IRQs 16 17 18 19) *11
[    0.252931] ACPI: PCI Interrupt Link [LN5B] (IRQs 16 17 18 19) *0, disabled.
[    0.253220] ACPI: PCI Interrupt Link [LN5C] (IRQs 16 17 18 19) *0, disabled.
[    0.253513] ACPI: PCI Interrupt Link [LN5D] (IRQs 16 17 18 19) *0, disabled.
[    0.253802] ACPI: PCI Interrupt Link [LN6A] (IRQs 16 17 18 19) *0, disabled.
[    0.254090] ACPI: PCI Interrupt Link [LN6B] (IRQs 16 17 18 19) *0, disabled.
[    0.254380] ACPI: PCI Interrupt Link [LN6C] (IRQs 16 17 18 19) *0, disabled.
[    0.254668] ACPI: PCI Interrupt Link [LN6D] (IRQs 16 17 18 19) *0, disabled.
[    0.254963] ACPI: PCI Interrupt Link [LUB0] (IRQs 20 21 22 23) *11
[    0.255256] ACPI: PCI Interrupt Link [LUB2] (IRQs 20 21 22 23) *9
[    0.255546] ACPI: PCI Interrupt Link [LMAC] (IRQs 20 21 22 23) *0, disabled.
[    0.255839] ACPI: PCI Interrupt Link [LAZA] (IRQs 20 21 22 23) *15
[    0.256136] ACPI: PCI Interrupt Link [sGRU] (IRQs 20 21 22 23) *14
[    0.256439] ACPI: PCI Interrupt Link [LSMB] (IRQs 20 21 22 23) *7
[    0.256740] ACPI: PCI Interrupt Link [LPMU] (IRQs 20 21 22 23) *10
[    0.257034] ACPI: PCI Interrupt Link [LSA0] (IRQs 20 21 22 23) *5
[    0.257373] ACPI: PCI Interrupt Link [LATA] (IRQs 20 21 22 23) *0, disabled.
[    0.257664] ACPI: PCI Interrupt Link [uB11] (IRQs 20 21 22 23) *0, disabled.
[    0.257954] ACPI: PCI Interrupt Link [uB12] (IRQs 20 21 22 23) *0, disabled.
[    0.258245] ACPI: PCI Interrupt Link [LRP0] (IRQs 20 21 22 23) *0, disabled.
[    0.258537] ACPI: PCI Interrupt Link [LRP1] (IRQs 20 21 22 23) *0, disabled.
[    0.258828] ACPI: PCI Interrupt Link [LRP2] (IRQs 20 21 22 23) *0, disabled.
[    0.259129] ACPI: PCI Interrupt Link [LRP3] (IRQs 20 21 22 23) *10
[    0.259429] ACPI: PCI Interrupt Link [LRP4] (IRQs 20 21 22 23) *11
[    0.259728] ACPI: PCI Interrupt Link [LRP5] (IRQs 20 21 22 23) *9
[    0.260026] ACPI: PCI Interrupt Link [LRP6] (IRQs 20 21 22 23) *15
[    0.260191] vgaarb: device added: PCI:0000:02:00.0,decodes=io+mem,owns=io+mem,locks=none
[    0.260200] vgaarb: loaded
[    0.260330] SCSI subsystem initialized
[    0.260436] libata version 3.00 loaded.
[    0.260513] usbcore: registered new interface driver usbfs
[    0.260529] usbcore: registered new interface driver hub
[    0.260559] usbcore: registered new device driver usb
[    0.260819] ACPI: WMI: Mapper loaded
[    0.260823] PCI: Using ACPI for IRQ routing
[    0.261099] NetLabel: Initializing
[    0.261103] NetLabel:  domain hash size = 128
[    0.261107] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.261122] NetLabel:  unlabeled traffic allowed by default
[    0.261162] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 31, 31
[    0.261171] hpet0: 4 comparators, 64-bit 25.000000 MHz counter
[    0.264144] Switching to clocksource tsc
[    0.266468] AppArmor: AppArmor Filesystem Enabled
[    0.266490] pnp: PnP ACPI init
[    0.266509] ACPI: bus type pnp registered
[    0.274154] pnp: PnP ACPI: found 13 devices
[    0.274162] ACPI: ACPI bus type pnp unregistered
[    0.274169] PnPBIOS: Disabled by ACPI PNP
[    0.274187] system 00:06: ioport range 0x4d0-0x4d1 has been reserved
[    0.274193] system 00:06: ioport range 0x800-0x80f has been reserved
[    0.274198] system 00:06: ioport range 0x4000-0x407f has been reserved
[    0.274204] system 00:06: ioport range 0x4080-0x40ff has been reserved
[    0.274209] system 00:06: ioport range 0x4400-0x447f has been reserved
[    0.274214] system 00:06: ioport range 0x4480-0x44ff has been reserved
[    0.274219] system 00:06: ioport range 0x4800-0x487f has been reserved
[    0.274224] system 00:06: ioport range 0x4880-0x48ff has been reserved
[    0.274231] system 00:06: iomem range 0xfefe2000-0xfefe3fff has been reserved
[    0.274237] system 00:06: iomem range 0xfefe1000-0xfefe1fff has been reserved
[    0.274242] system 00:06: iomem range 0xfee01000-0xfeefffff has been reserved
[    0.274252] system 00:09: iomem range 0xfec00000-0xfec00fff could not be reserved
[    0.274259] system 00:09: iomem range 0xfee00000-0xfee00fff has been reserved
[    0.274268] system 00:0b: iomem range 0xfc000000-0xfdffffff has been reserved
[    0.274276] system 00:0c: iomem range 0x0-0x9ffff could not be reserved
[    0.274282] system 00:0c: iomem range 0xc0000-0xcffff could not be reserved
[    0.274287] system 00:0c: iomem range 0xe0000-0xfffff could not be reserved
[    0.274292] system 00:0c: iomem range 0x100000-0xbfffffff could not be reserved
[    0.274299] system 00:0c: iomem range 0xfec00000-0xffffffff could not be reserved
[    0.309120] pci 0000:00:09.0: PCI bridge, secondary bus 0000:01
[    0.309131] pci 0000:00:09.0:   IO window: disabled
[    0.309138] pci 0000:00:09.0:   MEM window: disabled
[    0.309144] pci 0000:00:09.0:   PREFETCH window: disabled
[    0.309153] pci 0000:00:10.0: PCI bridge, secondary bus 0000:02
[    0.309159] pci 0000:00:10.0:   IO window: 0xc000-0xcfff
[    0.309166] pci 0000:00:10.0:   MEM window: 0xfaf00000-0xfbffffff
[    0.309173] pci 0000:00:10.0:   PREFETCH window: 0x000000e0000000-0x000000f5ffffff
[    0.309181] pci 0000:00:15.0: PCI bridge, secondary bus 0000:03
[    0.309189] pci 0000:00:15.0:   IO window: 0xd000-0xdfff
[    0.309202] pci 0000:00:15.0:   MEM window: 0xfe000000-0xfe9fffff
[    0.309212] pci 0000:00:15.0:   PREFETCH window: 0x000000f6000000-0x000000f9efffff
[    0.309230] pci 0000:00:16.0: PCI bridge, secondary bus 0000:06
[    0.309237] pci 0000:00:16.0:   IO window: 0xe000-0xefff
[    0.309250] pci 0000:00:16.0:   MEM window: 0xfea00000-0xfeafffff
[    0.309260] pci 0000:00:16.0:   PREFETCH window: 0x000000f9f00000-0x000000f9ffffff
[    0.309278] pci 0000:00:17.0: PCI bridge, secondary bus 0000:07
[    0.309282] pci 0000:00:17.0:   IO window: disabled
[    0.309295] pci 0000:00:17.0:   MEM window: 0xfeb00000-0xfebfffff
[    0.309305] pci 0000:00:17.0:   PREFETCH window: disabled
[    0.309321] pci 0000:00:18.0: PCI bridge, secondary bus 0000:08
[    0.309325] pci 0000:00:18.0:   IO window: disabled
[    0.309338] pci 0000:00:18.0:   MEM window: disabled
[    0.309347] pci 0000:00:18.0:   PREFETCH window: disabled
[    0.309372] pci 0000:00:09.0: setting latency timer to 64
[    0.309380] pci 0000:00:10.0: setting latency timer to 64
[    0.309843] ACPI: PCI Interrupt Link [LRP3] enabled at IRQ 23
[    0.309852]   alloc irq_desc for 23 on node -1
[    0.309855]   alloc kstat_irqs on node -1
[    0.309863] pci 0000:00:15.0: PCI INT A -> Link[LRP3] -> GSI 23 (level, low) -> IRQ 23
[    0.309875] pci 0000:00:15.0: setting latency timer to 64
[    0.310281] ACPI: PCI Interrupt Link [LRP4] enabled at IRQ 22
[    0.310289]   alloc irq_desc for 22 on node -1
[    0.310291]   alloc kstat_irqs on node -1
[    0.310295] pci 0000:00:16.0: PCI INT A -> Link[LRP4] -> GSI 22 (level, low) -> IRQ 22
[    0.310308] pci 0000:00:16.0: setting latency timer to 64
[    0.310712] ACPI: PCI Interrupt Link [LRP5] enabled at IRQ 21
[    0.310718]   alloc irq_desc for 21 on node -1
[    0.310720]   alloc kstat_irqs on node -1
[    0.310724] pci 0000:00:17.0: PCI INT A -> Link[LRP5] -> GSI 21 (level, low) -> IRQ 21
[    0.310737] pci 0000:00:17.0: setting latency timer to 64
[    0.311140] ACPI: PCI Interrupt Link [LRP6] enabled at IRQ 20
[    0.311146]   alloc irq_desc for 20 on node -1
[    0.311148]   alloc kstat_irqs on node -1
[    0.311152] pci 0000:00:18.0: PCI INT A -> Link[LRP6] -> GSI 20 (level, low) -> IRQ 20
[    0.311164] pci 0000:00:18.0: setting latency timer to 64
[    0.311171] pci_bus 0000:00: resource 0 io:  [0x00-0xffff]
[    0.311174] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
[    0.311177] pci_bus 0000:01: resource 3 io:  [0x00-0xffff]
[    0.311179] pci_bus 0000:01: resource 4 mem: [0x000000-0xffffffff]
[    0.311182] pci_bus 0000:02: resource 0 io:  [0xc000-0xcfff]
[    0.311185] pci_bus 0000:02: resource 1 mem: [0xfaf00000-0xfbffffff]
[    0.311188] pci_bus 0000:02: resource 2 pref mem [0xe0000000-0xf5ffffff]
[    0.311190] pci_bus 0000:03: resource 0 io:  [0xd000-0xdfff]
[    0.311193] pci_bus 0000:03: resource 1 mem: [0xfe000000-0xfe9fffff]
[    0.311195] pci_bus 0000:03: resource 2 pref mem [0xf6000000-0xf9efffff]
[    0.311198] pci_bus 0000:06: resource 0 io:  [0xe000-0xefff]
[    0.311201] pci_bus 0000:06: resource 1 mem: [0xfea00000-0xfeafffff]
[    0.311203] pci_bus 0000:06: resource 2 pref mem [0xf9f00000-0xf9ffffff]
[    0.311206] pci_bus 0000:07: resource 1 mem: [0xfeb00000-0xfebfffff]
[    0.311248] NET: Registered protocol family 2
[    0.311366] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.311729] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.312285] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[    0.312554] TCP: Hash tables configured (established 131072 bind 65536)
[    0.312560] TCP reno registered
[    0.312655] NET: Registered protocol family 1
[    0.343808] pci 0000:02:00.0: Boot video device
[    0.344029] cpufreq-nforce2: No nForce2 chipset.
[    0.344063] Scanning for low memory corruption every 60 seconds
[    0.344175] audit: initializing netlink socket (disabled)
[    0.344190] type=2000 audit(1277659619.343:1): initialized
[    0.354289] highmem bounce pool size: 64 pages
[    0.354304] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[    0.355904] VFS: Disk quotas dquot_6.5.2
[    0.355967] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.356574] fuse init (API version 7.13)
[    0.356662] msgmni has been set to 1655
[    0.356896] alg: No test for stdrng (krng)
[    0.356955] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    0.356962] io scheduler noop registered
[    0.356966] io scheduler anticipatory registered
[    0.356970] io scheduler deadline registered
[    0.357012] io scheduler cfq registered (default)
[    0.357358]   alloc irq_desc for 24 on node -1
[    0.357361]   alloc kstat_irqs on node -1
[    0.357383] pcieport 0000:00:15.0: irq 24 for MSI/MSI-X
[    0.357405] pcieport 0000:00:15.0: setting latency timer to 64
[    0.357777]   alloc irq_desc for 25 on node -1
[    0.357779]   alloc kstat_irqs on node -1
[    0.357797] pcieport 0000:00:16.0: irq 25 for MSI/MSI-X
[    0.357818] pcieport 0000:00:16.0: setting latency timer to 64
[    0.358191]   alloc irq_desc for 26 on node -1
[    0.358193]   alloc kstat_irqs on node -1
[    0.358211] pcieport 0000:00:17.0: irq 26 for MSI/MSI-X
[    0.358232] pcieport 0000:00:17.0: setting latency timer to 64
[    0.358602]   alloc irq_desc for 27 on node -1
[    0.358604]   alloc kstat_irqs on node -1
[    0.358622] pcieport 0000:00:18.0: irq 27 for MSI/MSI-X
[    0.358642] pcieport 0000:00:18.0: setting latency timer to 64
[    0.358810] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    0.358837] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    0.360093] ACPI: AC Adapter [ADP1] (on-line)
[    0.360205] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A03:00/device:00/PNP0C09:00/PNP0C0D:00/input/input0
[    0.361377] ACPI: Lid Switch [LID0]
[    0.361433] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
[    0.361440] ACPI: Power Button [PWRB]
[    0.361484] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input2
[    0.361495] ACPI: Sleep Button [sLPB]
[    0.361553] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[    0.361559] ACPI: Power Button [PWRF]
[    0.362297] ACPI: SSDT affae420 001FA (v01 MSI_NB MEGABOOK 09252009 INTL 20051117)
[    0.362944] ACPI: SSDT affae6b0 00594 (v01 MSI_NB MEGABOOK 09252009 INTL 20051117)
[    0.363476] Monitor-Mwait will be used to enter C-1 state
[    0.363505] Monitor-Mwait will be used to enter C-2 state
[    0.363529] Monitor-Mwait will be used to enter C-3 state
[    0.363535] Marking TSC unstable due to TSC halts in idle
[    0.363591] processor LNXCPU:00: registered as cooling_device0
[    0.363626] ACPI: SSDT affae350 000CC (v01 MSI_NB MEGABOOK 09252009 INTL 20051117)
[    0.363626] ACPI: SSDT affae620 00085 (v01 MSI_NB MEGABOOK 09252009 INTL 20051117)
[    0.363980] Switching to clocksource hpet
[    0.367987] processor LNXCPU:01: registered as cooling_device1
[    0.379179] thermal LNXTHERM:01: registered as thermal_zone0
[    0.379195] ACPI: Thermal Zone [THRM] (35 C)
[    0.380924] ******: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    0.382353] brd: module loaded
[    0.382853] loop: module loaded
[    0.382939] input: Macintosh mouse button emulation as /devices/virtual/input/input4
[    0.383504] ACPI: PCI Interrupt Link [LSA0] enabled at IRQ 23
[    0.383513] pata_acpi 0000:00:0b.0: PCI INT A -> Link[LSA0] -> GSI 23 (level, low) -> IRQ 23
[    0.383547] pata_acpi 0000:00:0b.0: setting latency timer to 64
[    0.383558] pata_acpi 0000:00:0b.0: PCI INT A disabled
[    0.383869] Fixed MDIO Bus: probed
[    0.383910] PPP generic driver version 2.4.2
[    0.383953] tun: Universal TUN/TAP device driver, 1.6
[    0.383957] tun: (C) 1999-2004 Max Krasnyansky 
[    0.384068] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.384482] ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 22
[    0.384489] ehci_hcd 0000:00:04.1: PCI INT B -> Link[LUB2] -> GSI 22 (level, low) -> IRQ 22
[    0.384506] ehci_hcd 0000:00:04.1: setting latency timer to 64
[    0.384510] ehci_hcd 0000:00:04.1: EHCI Host Controller
[    0.384546] ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 1
[    0.384573] ehci_hcd 0000:00:04.1: debug port 1
[    0.384585] ehci_hcd 0000:00:04.1: cache line size of 32 is not supported
[    0.384634] ehci_hcd 0000:00:04.1: irq 22, io mem 0xfae7ec00
[    0.384660] isapnp: Scanning for PnP cards...
[    0.385784] ACPI Exception: AE_BAD_PARAMETER, Returned by Handler for [EmbeddedControl] (20090903/evregion-424)
[    0.385797] ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0.SBRG.EC__.BAT1.UPBI] (Node f7016060), AE_BAD_PARAMETER
[    0.385838] ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0.SBRG.EC__.BAT1._BIF] (Node f7016000), AE_BAD_PARAMETER
[    0.385880] ACPI Exception: AE_BAD_PARAMETER, Evaluating _BIF (20090903/battery-363)
[    0.385889] ACPI: Battery Slot [bAT1] (battery present)
[    0.433564] ehci_hcd 0000:00:04.1: USB 2.0 started, EHCI 1.00
[    0.433719] usb usb1: configuration #1 chosen from 1 choice
[    0.433755] hub 1-0:1.0: USB hub found
[    0.433767] hub 1-0:1.0: 10 ports detected
[    0.433848] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    0.434315] ACPI: PCI Interrupt Link [LUB0] enabled at IRQ 21
[    0.434323] ohci_hcd 0000:00:04.0: PCI INT A -> Link[LUB0] -> GSI 21 (level, low) -> IRQ 21
[    0.434347] ohci_hcd 0000:00:04.0: setting latency timer to 64
[    0.434350] ohci_hcd 0000:00:04.0: OHCI Host Controller
[    0.434391] ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 2
[    0.434420] ohci_hcd 0000:00:04.0: irq 21, io mem 0xfae7f000
[    0.505498] Freeing initrd memory: 12210k freed
[    0.523441] usb usb2: configuration #1 chosen from 1 choice
[    0.523485] hub 2-0:1.0: USB hub found
[    0.523499] hub 2-0:1.0: 10 ports detected
[    0.523576] uhci_hcd: USB Universal Host Controller Interface driver
[    0.523690] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[    0.540447] serio: i8042 KBD port at 0x60,0x64 irq 1
[    0.540455] serio: i8042 AUX port at 0x60,0x64 irq 12
[    0.540584] mice: PS/2 mouse device common for all mice
[    0.541295] rtc_cmos 00:08: RTC can wake from S4
[    0.541340] rtc_cmos 00:08: rtc core: registered rtc_cmos as rtc0
[    0.541392] rtc0: alarms up to one year, y3k, 114 bytes nvram, hpet irqs
[    0.541496] device-mapper: uevent: version 1.0.3
[    0.541613] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[    0.541687] device-mapper: multipath: version 1.1.0 loaded
[    0.541693] device-mapper: multipath round-robin: version 1.0.0 loaded
[    0.541808] EISA: Probing bus 0 at eisa.0
[    0.541823] Cannot allocate resource for EISA slot 4
[    0.541839] EISA: Detected 0 cards.
[    0.541991] cpuidle: using governor ladder
[    0.542113] cpuidle: using governor menu
[    0.542586] TCP cubic registered
[    0.542741] NET: Registered protocol family 10
[    0.543254] lo: Disabled Privacy Extensions
[    0.543613] NET: Registered protocol family 17
[    0.544070] Using IPI No-Shortcut mode
[    0.544143] PM: Resume from disk failed.
[    0.544163] registered taskstats version 1
[    0.544754]   Magic number: 14:207:442
[    0.564719] rtc_cmos 00:08: setting system clock to 2010-06-27 17:27:00 UTC (1277659620)
[    0.564726] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    0.564730] EDD information not available.
[    0.575471] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input5
[    0.745848] isapnp: No Plug & Play device found
[    0.745873] Freeing unused kernel memory: 656k freed
[    0.746316] Write protecting the kernel text: 4676k
[    0.746367] Write protecting the kernel read-only data: 1840k
[    0.748035] usb 1-8: new high speed USB device using ehci_hcd and address 2
[    0.764733] udev: starting version 151
[    0.866828] [Firmware Bug]: ACPI(IGPU) defines _DOD but not _DOS
[    0.871835] acpi device:07: registered as cooling_device2
[    0.874362] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A03:00/device:06/LNXVIDEO:00/input/input6
[    0.874415] ACPI: Video Device [iGPU] (multi-head: yes  rom: no  post: no)
[    0.875197] ahci 0000:00:0b.0: version 3.0
[    0.875211] ahci 0000:00:0b.0: PCI INT A -> Link[LSA0] -> GSI 23 (level, low) -> IRQ 23
[    0.875260]   alloc irq_desc for 28 on node -1
[    0.875262]   alloc kstat_irqs on node -1
[    0.875272] ahci 0000:00:0b.0: irq 28 for MSI/MSI-X
[    0.875316] ahci 0000:00:0b.0: AHCI 0001.0200 32 slots 2 ports 3 Gbps 0x3 impl IDE mode
[    0.875323] ahci 0000:00:0b.0: flags: 64bit ncq sntf led pmp pio slum part 
[    0.875331] ahci 0000:00:0b.0: setting latency timer to 64
[    0.876685] scsi0 : ahci
[    0.876814] scsi1 : ahci
[    0.876913] ata1: SATA max UDMA/133 abar m8192@0xfae7c000 port 0xfae7c100 irq 28
[    0.876920] ata2: SATA max UDMA/133 abar m8192@0xfae7c000 port 0xfae7c180 irq 28
[    0.878011] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[    0.878466] ACPI: PCI Interrupt Link [LN4A] enabled at IRQ 19
[    0.878476]   alloc irq_desc for 19 on node -1
[    0.878478]   alloc kstat_irqs on node -1
[    0.878486] r8169 0000:06:00.0: PCI INT A -> Link[LN4A] -> GSI 19 (level, low) -> IRQ 19
[    0.878528] r8169 0000:06:00.0: setting latency timer to 64
[    0.878569]   alloc irq_desc for 29 on node -1
[    0.878571]   alloc kstat_irqs on node -1
[    0.878583] r8169 0000:06:00.0: irq 29 for MSI/MSI-X
[    0.879271] eth0: RTL8168c/8111c at 0xf80b8000, 00:24:22:20:f2:65, XID 1c4000c0 IRQ 29
[    1.071555] usb 1-8: configuration #1 chosen from 1 choice
[    1.208038] usb 1-10: new high speed USB device using ehci_hcd and address 3
[    1.351663] usb 1-10: configuration #1 chosen from 1 choice
[    1.360532] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    1.360553] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    1.362509] Initializing USB Mass Storage driver...
[    1.362612] scsi2 : SCSI emulation for USB Mass Storage devices
[    1.362697] usbcore: registered new interface driver usb-storage
[    1.362703] USB Mass Storage support registered.
[    1.362710] usb-storage: device found at 3
[    1.362712] usb-storage: waiting for device to settle before scanning
[    1.377568] ata2.00: ATAPI: HL-DT-STDVDRAM GT10N, 1.02, max UDMA/100, ATAPI AN
[    1.381590] ata2.00: configured for UDMA/100
[    1.413503] ata1.00: ATA-8: TOSHIBA MK2555GSX, FG001A, max UDMA/100
[    1.413513] ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32)
[    1.414358] ata1.00: configured for UDMA/100
[    1.414486] scsi 0:0:0:0: Direct-Access     ATA      TOSHIBA MK2555GS FG00 PQ: 0 ANSI: 5
[    1.414633] sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
[    1.414640] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    1.414722] sd 0:0:0:0: [sda] Write Protect is off
[    1.414727] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.414754] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.414904]  sda:
[    1.416812] scsi 1:0:0:0: CD-ROM            HL-DT-ST DVDRAM GT10N     1.02 PQ: 0 ANSI: 5
[    1.424474] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[    1.424485] Uniform CD-ROM driver Revision: 3.20
[    1.424634] sr 1:0:0:0: Attached scsi CD-ROM sr0
[    1.424685] sr 1:0:0:0: Attached scsi generic sg1 type 5
[    1.467661]  sda1 sda2 sda3 sda4
[    1.487937] sd 0:0:0:0: [sda] Attached SCSI disk
[    2.083213] uvesafb: NVIDIA Corporation, MCP79 Board - mcp79mvl, Chip Rev   , OEM: NVIDIA, VBE v3.0
[    2.107467] uvesafb: protected mode interface info at c000:ca00
[    2.107473] uvesafb: pmi: set display start = c00cca63, set palette = c00ccabe
[    2.107478] uvesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da 
[    2.171775] uvesafb: VBIOS/hardware doesn't support DDC transfers
[    2.171780] uvesafb: no monitor limits have been set, default refresh rate will be used
[    2.171947] uvesafb: scrolling: ywrap using protected mode interface, yres_virtual=1800
[    2.172918] uvesafb: framebuffer at 0xf5000000, mapped to 0xf8100000, using 10125k, total 14336k
[    2.172930] fb0: VESA VGA frame buffer device
[    2.595977] Console: switching to colour frame buffer device 180x56
[    2.901767] EXT4-fs (sda1): mounted filesystem with ordered data mode
[    6.360505] usb-storage: device scan complete
[    6.362595] scsi 2:0:0:0: Direct-Access     Generic- Multi-Card       1.00 PQ: 0 ANSI: 0 CCS
[    6.363133] sd 2:0:0:0: Attached scsi generic sg2 type 0
[    6.366931] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[   24.720963] udev: starting version 151
[   24.737433] Adding 2353512k swap on /dev/sda3.  Priority:-1 extents:1 across:2353512k 
[   24.787209] lp: driver loaded but no devices found
[   24.824227] Linux agpgart interface v0.103
[   24.995710] type=1505 audit(1277656044.927:2):  operation="profile_load" pid=666 name="/sbin/dhclient3"
[   24.996452] type=1505 audit(1277656044.927:3):  operation="profile_load" pid=666 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
[   24.996817] type=1505 audit(1277656044.931:4):  operation="profile_load" pid=666 name="/usr/lib/connman/scripts/dhclient-script"
[   25.008729] nvidia: module license 'NVIDIA' taints kernel.
[   25.008732] Disabling lock debugging due to kernel taint
[   25.828870] i2c i2c-0: nForce2 SMBus adapter at 0x4d00
[   25.828876] ACPI: resource nForce2_smbus [0x4e00-0x4e3f] conflicts with ACPI region SM00 [0x4e00-0x4e3f]
[   25.828879] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   25.828882] nForce2_smbus 0000:00:03.2: Error probing SMB2.
[   25.830962] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   25.863033] Linux video capture interface: v2.00
[   25.868562] lirc_dev: IR Remote Control driver registered, major 61 
[   25.869573] uvcvideo: Found UVC 1.00 device BisonCam, NB Pro (5986:0203)
[   25.870517] cfg80211: Calling CRDA to update world regulatory domain
[   25.885849] input: BisonCam, NB Pro as /devices/pci0000:00/0000:00:04.1/usb1/1-8/1-8:1.0/input/input7
[   25.886000] usbcore: registered new interface driver uvcvideo
[   25.886604] USB Video Class driver (v0.1.0)
[   25.899032] ACPI: PCI Interrupt Link [LN5A] enabled at IRQ 18
[   25.899040]   alloc irq_desc for 18 on node -1
[   25.899042]   alloc kstat_irqs on node -1
[   25.899050] ath5k 0000:07:00.0: PCI INT A -> Link[LN5A] -> GSI 18 (level, low) -> IRQ 18
[   25.899060] ath5k 0000:07:00.0: setting latency timer to 64
[   25.899093] ath5k 0000:07:00.0: registered as 'phy0'
[   26.085960] ACPI: PCI Interrupt Link [LPMU] enabled at IRQ 20
[   26.085967] nvidia 0000:00:03.5: PCI INT B -> Link[LPMU] -> GSI 20 (level, low) -> IRQ 20
[   26.086384] ACPI: PCI Interrupt Link [sGRU] enabled at IRQ 23
[   26.086387] nvidia 0000:02:00.0: PCI INT A -> Link[sGRU] -> GSI 23 (level, low) -> IRQ 23
[   26.086394] nvidia 0000:02:00.0: setting latency timer to 64
[   26.086398] vgaarb: device changed decodes: PCI:0000:02:00.0,olddecodes=io+mem,decodes=none:owns=io+mem
[   26.087189] NVRM: loading NVIDIA UNIX x86 Kernel Module  195.36.24  Thu Apr 22 09:18:20 PDT 2010
[   26.146498] vga16fb: initializing
[   26.146502] vga16fb: mapped to 0xc00a0000
[   26.146506] vga16fb: not registering due to another framebuffer present
[   26.290877] HDA Intel 0000:00:08.0: power state changed by ACPI to D0
[   26.291296] ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 22
[   26.291302] HDA Intel 0000:00:08.0: PCI INT A -> Link[LAZA] -> GSI 22 (level, low) -> IRQ 22
[   26.291305] hda_intel: Disable MSI for Nvidia chipset
[   26.291335] HDA Intel 0000:00:08.0: setting latency timer to 64
[   26.315768] lirc_dev: lirc_register_driver: sample_rate: 0
[   26.315891] enecir: KB3926B detected
[   26.315893] enecir: chip is 0x3909 - 0x24, 0xc0
[   26.315895] enecir: driver has been succesfully loaded
[   26.337161] cfg80211: World regulatory domain updated:
[   26.337164]     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   26.337167]     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   26.337170]     (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   26.337173]     (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   26.337176]     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   26.337178]     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   26.388674] psmouse serio1: ID: 10 00 64
[   26.397497] ath: EEPROM regdomain: 0x60
[   26.397499] ath: EEPROM indicates we should expect a direct regpair map
[   26.397503] ath: Country alpha2 being used: 00
[   26.397505] ath: Regpair used: 0x60
[   26.404359] phy0: Selected rate control algorithm 'minstrel'
[   26.405166] Registered led device: ath5k-phy0::rx
[   26.405184] Registered led device: ath5k-phy0::tx
[   26.405187] ath5k phy0: Atheros AR2425 chip found (MAC: 0xe2, PHY: 0x70)
[   26.551620] elantech.c: assuming hardware version 1, firmware version 1.33
[   26.554134] type=1505 audit(1277656046.487:5):  operation="profile_load" pid=864 name="/usr/sbin/mysqld"
[   26.575387] type=1505 audit(1277656046.507:6):  operation="profile_load" pid=883 name="/usr/share/gdm/guest-session/Xsession"
[   26.578795] type=1505 audit(1277656046.511:7):  operation="profile_replace" pid=887 name="/sbin/dhclient3"
[   26.579493] type=1505 audit(1277656046.511:8):  operation="profile_replace" pid=887 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
[   26.579867] type=1505 audit(1277656046.511:9):  operation="profile_replace" pid=887 name="/usr/lib/connman/scripts/dhclient-script"
[   26.585083] type=1505 audit(1277656046.519:10):  operation="profile_load" pid=888 name="/usr/bin/evince"
[   26.594432] type=1505 audit(1277656046.527:11):  operation="profile_load" pid=888 name="/usr/bin/evince-previewer"
[   26.617058] elantech.c: Synaptics capabilities query result 0x02, 0x02, 0x64.
[   27.054690] input: E***/2 Elantech Touchpad as /devices/platform/i8042/serio1/input/input8

 

les lignes en question sont :

6.362595] scsi 2:0:0:0: Direct-Access Generic- Multi-Card 1.00 PQ: 0 ANSI: 0 CCS

[ 6.363133] sd 2:0:0:0: Attached scsi generic sg2 type 0

[ 6.366931] sd 2:0:0:0: [sdb] Attached SCSI removable disk

Link to comment
Share on other sites

Il ne peut pas ignorer l'existence d'un lecteur de carte mémoire. Comment veux-tu qu'il lise des cartes mémoire si tu désactives son support au démarrage, il ne vérifie pas s'il y a une carte dans le slot au début mais l'état du lecteur ;)

Link to comment
Share on other sites

sinon tu peu essayer de dire a udev de l'ignorer :

 

le fichier correspondant est :

 

/etc/udev/rules.d/60-persistent-storage.rules

cherche la ligne :

# skip rules for inappropriate block devices
KERNEL=="ram*|loop*|fd*|nbd*|gnbd*|dm-*|md*", GOTO="persistent_storage_end"

et rajoute sdb*

 

KERNEL=="ram*|loop*|fd*|nbd*|gnbd*|dm-*|md*|sdb*", GOTO="persistent_storage_end"

save and reboot

Link to comment
Share on other sites

comment est-ce qu'il est branché avec la carte mère : probablement usb ? si oui moi g l'option de désactivé un port usb au choix dans mon bios et même les autres interface sont désactivable au choix sata1 sata2 ... a part si c un laptop généralement leur bios ne contiennent pas beaucoup d'option

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...